engine is back in, just need to connect all the wiring back up
pistons are nice and clean now too
yeah looked at the MLS gaskets, only place I could find that had them wanted $195 each
hopefully no issues when I kick it in the guts tomorrow
Search found 72 matches
- Tue Apr 16, 2013 9:19 pm
- Forum: Members Rides
- Topic: The1's Daily
- Replies: 682
- Views: 276024
- Mon Apr 15, 2013 11:20 pm
- Forum: Members Rides
- Topic: The1's Daily
- Replies: 682
- Views: 276024
Re: The1's Daily
were ACL monotorque that came with the ACL rebuild kit I used
does not appear to be any damage to the head or block, need to get a straight edge in the morning to check the head before putting it all back together
Hopefully no warping otherwise its a trip to get them machined
does not appear to be any damage to the head or block, need to get a straight edge in the morning to check the head before putting it all back together
Hopefully no warping otherwise its a trip to get them machined
- Mon Apr 15, 2013 10:11 pm
- Forum: Members Rides
- Topic: The1's Daily
- Replies: 682
- Views: 276024
Re: The1's Daily
took the heads off today after pulling the engine out knew I should have taken them off first but anyway rings are OK
no need to tear motor down, just need to check that it has not been warped
no need to tear motor down, just need to check that it has not been warped
- Mon Apr 15, 2013 7:54 am
- Forum: Members Rides
- Topic: The1's Daily
- Replies: 682
- Views: 276024
Re: The1's Daily
yep same guy have done all the mods he suggests, deburring the oil pump area of the timing cover, adding drip holes over each cam lobe will see what my bearing look like after around 20K of use as I am about to pull the engine out due to developing some major blow by a couple of days ago :rant: Hope...
- Sun Apr 14, 2013 8:01 pm
- Forum: Members Rides
- Topic: The1's Daily
- Replies: 682
- Views: 276024
Re: The1's Daily
yeah oil galley is one of the ones that you do for the oil mod on these engines, from memory the oil feed for the big ends are fed from the smallest oil galley normally you take them out to 7/16 or 3/8, on one of the other forums some guys have said that with 3/8 you can loose oil pressure if left i...
- Fri Apr 05, 2013 4:19 pm
- Forum: Engine/Transmision Mechanical
- Topic: VN-VS front sway bar links, downgrading (aka upgrading?)
- Replies: 33
- Views: 28035
Re: VN-VS front sway bar links, downgrading (aka upgrading?)
there is this one
http://www.ebay.com.au/itm/290507322416 ... 767wt_1037
I think whiteline or nolathane also make them now too
http://www.ebay.com.au/itm/290507322416 ... 767wt_1037
I think whiteline or nolathane also make them now too
- Sat Mar 30, 2013 11:15 am
- Forum: Members Rides
- Topic: My Delcoed Rides
- Replies: 1229
- Views: 510010
Re: My Delcoed Rides
can't wait to hear how the new engine goes at the track
second leaving the tune the way it is, sounds tough as
second leaving the tune the way it is, sounds tough as
- Tue Mar 26, 2013 8:25 pm
- Forum: General Tuning Discussion
- Topic: Is there anything more to be had from a stock tune on a L67?
- Replies: 3
- Views: 2566
Re: Is there anything more to be had from a stock tune on a
Given you have slightly higher boost I would say yes, if you have an wideband O2 sensor fitted you will get more accurate tuning on it
- Sun Mar 17, 2013 7:49 am
- Forum: Tools
- Topic: Innovate LM2 Wideband Info
- Replies: 56
- Views: 34704
Re: Innovate LM2 Wideband Info
is it just in TP that the WB is out or is the display of the WB itself also out?
If it is just your reading in TP then the calculation needs tweeking
I have the Innovate WB and the reading in TP and the display of the WB are within 0.1 AFR of each other
If it is just your reading in TP then the calculation needs tweeking
I have the Innovate WB and the reading in TP and the display of the WB are within 0.1 AFR of each other
- Sun Mar 17, 2013 7:36 am
- Forum: Members Rides
- Topic: Vlad's rides thread
- Replies: 3386
- Views: 1349682
Re: Vlad's VP executive (full restro)
the cluster looks to be in great nick
The door trim turned out great, did you just use vinyl paint or something else?
The door trim turned out great, did you just use vinyl paint or something else?