Search found 568 matches
- Fri Feb 23, 2018 8:00 am
- Forum: Hardware Modification and Development
- Topic: LSx Coil Driver
- Replies: 154
- Views: 167301
Re: LSx Coil Driver
Can anyone confirm the factory dwell time on a VS Ecotec? Setting up VL400s coil driver with some monster coils and treading carefully
- Thu Feb 08, 2018 6:40 pm
- Forum: General Tuning Discussion
- Topic: $11P idle timing reverting to max
- Replies: 10
- Views: 6394
Re: $11P idle timing reverting to max
This car was a conversion and came in without a comms port which I ended up wiring in.
The wires were taped direct to the loom and seemed to be dropping data on read and writes and corrupting the memcal.
I insulated comms wiring better away from the main loom and happy days
The wires were taped direct to the loom and seemed to be dropping data on read and writes and corrupting the memcal.
I insulated comms wiring better away from the main loom and happy days
- Sat Feb 03, 2018 4:31 pm
- Forum: General Tuning Discussion
- Topic: $11P idle timing reverting to max
- Replies: 10
- Views: 6394
Re: $11P idle timing reverting to max
Yep good call, first thing I tried. I also removed the DS1245Y and erased, re burned the original bas tune I started on months back to no availHolden202T wrote:what about a stock bin on the nvram just to see if it fixes it ?
- Sat Feb 03, 2018 3:04 pm
- Forum: General Tuning Discussion
- Topic: $11P idle timing reverting to max
- Replies: 10
- Views: 6394
Re: $11P idle timing reverting to max
Yep but have only done it 3 times so far haha.Dylan wrote:Done a compare to a stock bin to check all changes are sane?
- Sat Feb 03, 2018 11:13 am
- Forum: General Tuning Discussion
- Topic: $11P idle timing reverting to max
- Replies: 10
- Views: 6394
Re: $11P idle timing reverting to max
are you saying the timing as seen with a timing light is 60 degrees or the data logging is showing it command 60 degrees ? I wouldn't think it would run at all with 60 degrees even with 45 or more it would be on the next cylinder! Timing light is spot on in diagnostic mode. Log shows 60 degrees and...
- Sat Feb 03, 2018 6:44 am
- Forum: General Tuning Discussion
- Topic: $11P idle timing reverting to max
- Replies: 10
- Views: 6394
$11P idle timing reverting to max
Touching up a previously successfully tuned VS 5L on $11P after next round of mods and all of a sudden the idle timing has irreversibly reverted to max of 60 deg no matter what. I played with the max allowable timing parameter to test where the timing figure is been derived from as well as comparing...
- Thu Jan 25, 2018 4:50 pm
- Forum: Engine/Transmision Mechanical
- Topic: Ecotec tie bar lifters - where to get???
- Replies: 20
- Views: 17365
Re: Ecotec tie bar lifters - where to get???
how much noiser do you think they'll be than standard lifters? I've heard they can be pretty noisy which makes the knock sensors a bit useless Set pre load right and they're going to be fine. Most forget that it's usually a crazy cam profile fitted in conjunction with aftermarket style lifters that...
- Tue Jan 09, 2018 11:58 am
- Forum: General Tuning Discussion
- Topic: vy v6 turbo knock
- Replies: 5
- Views: 3024
Re: vy v6 turbo knock
May pay to double check turbo health too. I've seen heaps that lock up under spool when the core is a bit crappy
- Tue Dec 12, 2017 10:35 am
- Forum: Members Rides
- Topic: KE70 track car project
- Replies: 84
- Views: 58114
Re: KE70 track car project
Thread dig, sorry What's the theory behind the rear control arms, and them being the same lenght? Pinion angle is where it's at for us. Even though there are no bushes and all Heim joints, there will undoubtedly be some angle change of the pinion under power down. We've found that setting the pinio...
- Tue Nov 28, 2017 5:06 pm
- Forum: Custom Code
- Topic: VS-VY Enhanced Factory Bins
- Replies: 836
- Views: 758745
Re: The1's Enhanced Factory Bins
I just updated the OSE plug in and happy daysdelcowizzid wrote:Should just work .what version of the oseplugin do you have .you could try logging with tunerpro I/O instead of the plugin and see if it connects to log.