OSE 12P V112
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: OSE 12P V112
12p just works when you plug in the wideband and set the 0 and 5v air fuel ratios I've never had any issues. I just did a cammed 304 in a vr a couple of weeks ago went from 120rwkw to 196rwkw cam springs and tune the airbox was a restriction at that level even with hsv otr. With the lid off the box and no filter it gained 6rwkw haha
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
- Posts: 1
- Joined: Sun Apr 03, 2011 9:44 pm
- cars: holden vt 3.8l and vt 5.0l
Re: OSE 12P V112
If anyone wants a XDF file categorized like the 11P one here it is.
no other changes made other than sorting everything into categories the same as 11p to make it easier to change from one to the other
no other changes made other than sorting everything into categories the same as 11p to make it easier to change from one to the other
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: OSE 12P V112
Can you change the name and reupload add maybe catagarised to the end be nice to not have multi xdfs floating around with the same name it confuses peoe haha
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: OSE 12P V112
i've done it
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: OSE 12P V112
Cheers
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- antus
- Site Admin
- Posts: 8259
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: OSE 12P V112
linked from first post, thanks!
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 45
- Joined: Mon Apr 03, 2017 2:33 am
- cars: S10's with TPI
S10 with '165 turbo 4 cyl
TPI Camaro
Re: OSE 12P V112
Knock Count logging and wiring question.
Have a '165 computer running at boosted 4 cyl. Runs well, but I would like to add in knock logging if possible. I have a GM knock sensor and filter setup that was common on the TPI engines. Can I use this as an input for 12P to log knock counts?
Looking for some wiring advice and config changes to add this in.
Mark.
Have a '165 computer running at boosted 4 cyl. Runs well, but I would like to add in knock logging if possible. I have a GM knock sensor and filter setup that was common on the TPI engines. Can I use this as an input for 12P to log knock counts?
Looking for some wiring advice and config changes to add this in.
Mark.
- antus
- Site Admin
- Posts: 8259
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: OSE 12P V112
You need the knock filter on the memcal like the aussie ones, and its an audio frequency filter that is build to suit the engine the memcal is for and can not be tuned to a different engine type. I dont think what you have is compatible. If your engine has the same bore as the engine the factory knock board was built for you will get some results, but the factory system was early and doesnt compare to modern systems. Further if you've matched the bore but its a different engine your results will likely be worse than the so-so factory system. I would recommend you dont use it. You can see a pic of the right type of knock board here - its the white board next to the chip. viewtopic.php?t=214&start=120#p81644
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
- vlad01
- Posts: 7823
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: OSE 12P V112
I found the factory knock control system very hit and miss like Antus said, it's very early and primitive.
I find most of the time it triggers from gearbox noise and exhaust pulses when you have headers. And the worst part is, most of the time it doesn't even register real knock when I verified with knock headphones on the dyno.
I disable all settings related to knock and just tune in a little safety margin in the spark table with knock headphones.
If you want knock control it may be possible to run a external knock box like the G4 that HP academy showed years ago into one of the inputs and run a flex table to retard the timing but I think it will still be crude compared to modern ECUs
I find most of the time it triggers from gearbox noise and exhaust pulses when you have headers. And the worst part is, most of the time it doesn't even register real knock when I verified with knock headphones on the dyno.
I disable all settings related to knock and just tune in a little safety margin in the spark table with knock headphones.
If you want knock control it may be possible to run a external knock box like the G4 that HP academy showed years ago into one of the inputs and run a flex table to retard the timing but I think it will still be crude compared to modern ECUs
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
- Posts: 45
- Joined: Mon Apr 03, 2017 2:33 am
- cars: S10's with TPI
S10 with '165 turbo 4 cyl
TPI Camaro
Re: OSE 12P V112
Yes I have used that knock filter on the PROM in the later GM ECMs I used (7730s). The external one is essentially the same, just external. I could match the bore up with a similar one from a V8 application.antus wrote:You need the knock filter on the memcal like the aussie ones, and its an audio frequency filter that is build to suit the engine the memcal is for and can not be tuned to a different engine type. I dont think what you have is compatible. If your engine has the same bore as the engine the factory knock board was built for you will get some results, but the factory system was early and doesnt compare to modern systems. Further if you've matched the bore but its a different engine your results will likely be worse than the so-so factory system. I would recommend you dont use it. You can see a pic of the right type of knock board here - its the white board next to the chip. viewtopic.php?t=214&start=120#p81644
I was curious to see if I could log any knocks and see.
If I was to use the PROM piggy back, then I connect knock sensor to ECM Pin? I didn't think the piggy back filter worked with the '165s.
Mark.