Setting up Wideband Datalogging Input Video
Setting up Wideband Datalogging Input Video
Here's me again with my dumb voice, hope you guys enjoy and get something usefull from it. Arh it's late im off.
[youtube]https://www.youtube.com/watch?v=58svlSl6Duo[/youtube]
[youtube]https://www.youtube.com/watch?v=58svlSl6Duo[/youtube]
Re: Setting up Wideband Datalogging Input Video
I thought vlad was volunteering for the next how to vid nice work anyway mate
- vlad01
- Posts: 7823
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Setting up Wideband Datalogging Input Video
Dazza92VP wrote:I thought vlad was volunteering for the next how to vid nice work anyway mate
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Setting up Wideband Datalogging Input Video
Good video mate
On a side note for those with 11P or 12P you do not need to change the ADX calc, its always left as X/10. There are two scalars you set to match the 0V and 5V AFR points (ie 0V=11AFR and 5V=17AFR if the wideband analog output is setup as discussed in this video), everything else is handled behind the scenes for you.
On a side note for those with 11P or 12P you do not need to change the ADX calc, its always left as X/10. There are two scalars you set to match the 0V and 5V AFR points (ie 0V=11AFR and 5V=17AFR if the wideband analog output is setup as discussed in this video), everything else is handled behind the scenes for you.
Re: Setting up Wideband Datalogging Input Video
11P is available to the public now??
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Setting up Wideband Datalogging Input Video
I think what he is referring to is that's how its setup in both, when its available that is
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vlad01
- Posts: 7823
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Setting up Wideband Datalogging Input Video
question about the spartan WB, they state their output is 10AFR @ 0V and 20AFR @ 5V.
I put in those values in 12P, if the sensor is just running in the open air, should it peg out to 20AFR? cos it pegs out to 18.7AFR.
If I saturate the sensor with propane gas, its drops to min of 10AFR which is what I expect.
I put in those values in 12P, if the sensor is just running in the open air, should it peg out to 20AFR? cos it pegs out to 18.7AFR.
If I saturate the sensor with propane gas, its drops to min of 10AFR which is what I expect.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Setting up Wideband Datalogging Input Video
put a multi meter on the wideband output... does it get to 5V in open air?
I would suspect a bad earth on wideband maybe and hte ecu is not seeing the full 5v from the wideband.
I would suspect a bad earth on wideband maybe and hte ecu is not seeing the full 5v from the wideband.
Re: Setting up Wideband Datalogging Input Video
My 14.7 kit does the same. Cant remember the reading but around that.
Im about to put the narrow band back in so see how if compares. As I have nothing to check my readings in tuner pro against.
Im about to put the narrow band back in so see how if compares. As I have nothing to check my readings in tuner pro against.