Delco PIS firmware soon.. :)
-
- Posts: 13
- Joined: Sun Oct 18, 2009 1:14 am
- cars: VN turbo, LJ Torana turbo, 2 x ZXR 750, Porsche. VK SC14
Delco PIS firmware soon.. :)
Hi,
Something you might be interested in.. over the last few months I have written a 100% custom firmware for the 808 delco to make it a more generic ECU. In combination with VL400's NVRAM boards they will be adjustable on the fly. This is a base code to be released under GPL3 yep. The source code will be available for your additions has wideband support, boost control etc + whatever other folks add. The ECU will operate more like aftermarket ECU's and is not a direct replacement for your car but rather for your created projects. I have been working with Dave J Andruczyk to bring delco compatability in the base of MegaTunix!! Tuner Pro compatibility is just a plug-in away. nice I have a tease picture attached ~
Regards
Jay
Please refrain from contacting Dave for support regarding the MegaTunix & the delco project. Thanks for your understanding you may contact myself instead.
Something you might be interested in.. over the last few months I have written a 100% custom firmware for the 808 delco to make it a more generic ECU. In combination with VL400's NVRAM boards they will be adjustable on the fly. This is a base code to be released under GPL3 yep. The source code will be available for your additions has wideband support, boost control etc + whatever other folks add. The ECU will operate more like aftermarket ECU's and is not a direct replacement for your car but rather for your created projects. I have been working with Dave J Andruczyk to bring delco compatability in the base of MegaTunix!! Tuner Pro compatibility is just a plug-in away. nice I have a tease picture attached ~
Regards
Jay
Please refrain from contacting Dave for support regarding the MegaTunix & the delco project. Thanks for your understanding you may contact myself instead.
- Attachments
-
- soon.jpg (453.97 KiB) Viewed 17265 times
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco PIS firmware soon.. :)
looks pretty cool to me ....
just out of interest, other than having to tune said engine would their be any disadvantages of using this over say $12P etc ?
like are all the factory nice bits still in it ?
just out of interest, other than having to tune said engine would their be any disadvantages of using this over say $12P etc ?
like are all the factory nice bits still in it ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- antus
- Site Admin
- Posts: 8261
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Delco PIS firmware soon.. :)
Thats completely awesome.
808 is good, but I imagine that in time it would be possible to port it to newer ecus too, without starting from scratch?
808 is good, but I imagine that in time it would be possible to port it to newer ecus too, without starting from scratch?
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: Delco PIS firmware soon.. :)
sounds great! will it do custom crank triggers?
-
- Posts: 13
- Joined: Sun Oct 18, 2009 1:14 am
- cars: VN turbo, LJ Torana turbo, 2 x ZXR 750, Porsche. VK SC14
Re: Delco PIS firmware soon.. :)
Hi,
holden202:
You can't really compare it with 12P horses for courses I say . no BCM, tq lockup, etc. Not intended for street use but rather race projects etc. I would think having MegaTunix dashboards and gauge designer to be advantageous great for your cheap modified stock car, drag car, boat etc.
antus
Thanks for Antusprom, it was invaluable during development. Yes parts of the code are pretty generic and can be used for other projects the main loop is in C the interpolation math is in asm for speed / size.
ejukated:
In short, not at the moment, however it will , 36-1 wheels etc. with some *magic* I have an ignition system that will be unleashed in due time, it basically lies to the ecu about pulses, so that controls it's fueling yet it can still take the timing commanded by the ECU.
I am looking for a couple of testers, even on the bench will help...
Regards
Jay
holden202:
You can't really compare it with 12P horses for courses I say . no BCM, tq lockup, etc. Not intended for street use but rather race projects etc. I would think having MegaTunix dashboards and gauge designer to be advantageous great for your cheap modified stock car, drag car, boat etc.
antus
Thanks for Antusprom, it was invaluable during development. Yes parts of the code are pretty generic and can be used for other projects the main loop is in C the interpolation math is in asm for speed / size.
ejukated:
In short, not at the moment, however it will , 36-1 wheels etc. with some *magic* I have an ignition system that will be unleashed in due time, it basically lies to the ecu about pulses, so that controls it's fueling yet it can still take the timing commanded by the ECU.
I am looking for a couple of testers, even on the bench will help...
Regards
Jay
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco PIS firmware soon.. :)
i would be willing to test it in my Gemini ... only thing i see being an issue is at the moment im using 12P flex table to control my electric water pump (thats all the engine has) .... is there anything in this program that i can use ? at the very worst i can wire in a switch to manually control it but would prefer not to if i don't have to.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Delco PIS firmware soon.. :)
Nice work Jay, looking forward to the final product
I can bench test it for you if you want.
I can bench test it for you if you want.
-
- Posts: 13
- Joined: Sun Oct 18, 2009 1:14 am
- cars: VN turbo, LJ Torana turbo, 2 x ZXR 750, Porsche. VK SC14
Re: Delco PIS firmware soon.. :)
Thanks guys,
Appreciate it I will send some files shortly.
Regards
Jay
Appreciate it I will send some files shortly.
Regards
Jay
- TTVN
- Posts: 194
- Joined: Tue Jun 30, 2009 10:01 pm
- cars: TT 355 VN, Rearmount turbo 355 vp, cammed 355 hj60 landcruiser, vx clubby n efilive VZ ls1 wagon
Re: Delco PIS firmware soon.. :)
Hi jay
Id be interested in trying it in my 355 landcruiser for fun
cheers Rod
Id be interested in trying it in my 355 landcruiser for fun
cheers Rod
-
- Posts: 13
- Joined: Sun Oct 18, 2009 1:14 am
- cars: VN turbo, LJ Torana turbo, 2 x ZXR 750, Porsche. VK SC14
Re: Delco PIS firmware soon.. :)
Hi,
You can download the files from http://github.com/torture/PIS as for MegaTunix you can get it direct from Dave's repo as all the PIS support is merged into the main trunk of MTX http://github.com/djandruczyk built binaries will not currently work, it must be compiled with the funky 8192 baud which requires a command line switch during configuration before the build. The PIS code expects to sit from 0x8000 0xffff.
on a linux box:-
to fetch and build PIS you will need a 68hc11 compiler suite installed if yours differs from mine check the README for setting your compiler, linker, etc. and of course for being able to edit settings on the fly you need nvram installed.
git clone http://github.com/Torture/PIS.git
cd PIS
make
the .s19 file is your target
to fetch and build MegaTunix:-
git clone http://github.com/djandruczyk/MegaTunix.git
cd MegaTunix
./autogen.sh --enable-pis --enabled-debug
make
sudo make install
cross compiling mtx for windows is another game but not impossible. There is an .s19 file ready for loading onto an ECU if you get that going (the first thing you will notice when powering the ECU on is the IAC valve will fully retract then move to it's "home" position) but can't figure to get MTX going let me know and I can build a windows installer version.
Regards
Jay
You can download the files from http://github.com/torture/PIS as for MegaTunix you can get it direct from Dave's repo as all the PIS support is merged into the main trunk of MTX http://github.com/djandruczyk built binaries will not currently work, it must be compiled with the funky 8192 baud which requires a command line switch during configuration before the build. The PIS code expects to sit from 0x8000 0xffff.
on a linux box:-
to fetch and build PIS you will need a 68hc11 compiler suite installed if yours differs from mine check the README for setting your compiler, linker, etc. and of course for being able to edit settings on the fly you need nvram installed.
git clone http://github.com/Torture/PIS.git
cd PIS
make
the .s19 file is your target
to fetch and build MegaTunix:-
git clone http://github.com/djandruczyk/MegaTunix.git
cd MegaTunix
./autogen.sh --enable-pis --enabled-debug
make
sudo make install
cross compiling mtx for windows is another game but not impossible. There is an .s19 file ready for loading onto an ECU if you get that going (the first thing you will notice when powering the ECU on is the IAC valve will fully retract then move to it's "home" position) but can't figure to get MTX going let me know and I can build a windows installer version.
Regards
Jay