Already got a few stock reads, this would of been what I used as the base file originally.kur4o wrote:Great that makes sense now.
Can you make a new fresh read of the 2011 pcm
I am almost done with the setiing and may try some combos.
Segment Swap utility
- Tre-Cool
- Posts: 318
- Joined: Tue Oct 16, 2012 12:17 pm
- cars: VY SS UTE, VX Drag Car
- Location: Perth
- Contact:
Re: Segment Swap utility
Re: Segment Swap utility
Flash this file OS+cal data. Than make a fresh read and post the file I want to be sure no remnants of previous patches are left in the pcm.
I am not sure it will run with this base stock file due to injectors and other stuff. If you want I can modify other file for flashing.
I am not sure it will run with this base stock file due to injectors and other stuff. If you want I can modify other file for flashing.
- Attachments
-
- GM E38 12639270-Manual_VATSoff_v1.bin
- (2 MiB) Downloaded 363 times
Re: Segment Swap utility
Some updates.
Tons of new features.
Now you can edit eeprom info.
Also much better support for e55 and e69 pcms.
There are some complete e55 definitions for saab cars, but I am sure they can be used for templates for sure.
-E55 and e69 beta DTC discovery and editing.
-Added some initial support for specific bosch e55 checksums[not sure they are used yet].
-reading of gm calibration identifier, good for different p/ns that are mapped the same.
-works only with full bin files[I noticed there are some e55 files that contain only caldata parts-it won`t work with those].
Tons of new features.
Now you can edit eeprom info.
Also much better support for e55 and e69 pcms.
There are some complete e55 definitions for saab cars, but I am sure they can be used for templates for sure.
-E55 and e69 beta DTC discovery and editing.
-Added some initial support for specific bosch e55 checksums[not sure they are used yet].
-reading of gm calibration identifier, good for different p/ns that are mapped the same.
-works only with full bin files[I noticed there are some e55 files that contain only caldata parts-it won`t work with those].
- Brian_Griffin
- Posts: 5
- Joined: Sat May 22, 2021 1:27 pm
- cars: Silverado, Trailblazer
Re: Segment Swap utility
Awesome work....Very much appreciated!kur4o wrote:Some updates.
Tons of new features.
Now you can edit eeprom info.
Also much better support for e55 and e69 pcms.
There are some complete e55 definitions for saab cars, but I am sure they can be used for templates for sure.
-E55 and e69 beta DTC discovery and editing.
-Added some initial support for specific bosch e55 checksums[not sure they are used yet].
-reading of gm calibration identifier, good for different p/ns that are mapped the same.
-works only with full bin files[I noticed there are some e55 files that contain only caldata parts-it won`t work with those].
Re: Segment Swap utility
I'm trying to disable catalytic protection in 12585950 OS
I've disabled DTCs, but i want to disable the system.
The only table i've found is Cat Light off.
Where are the requiered tables?
I've disabled DTCs, but i want to disable the system.
The only table i've found is Cat Light off.
Where are the requiered tables?
Re: Segment Swap utility
Try lowering COT_temperature_stoich_stable in the converter category.
It will put predicted temp of cat off chart.
I hope you are using this on an offroad vehicle.
I might the logic switch if I have time.
It will put predicted temp of cat off chart.
I hope you are using this on an offroad vehicle.
I might the logic switch if I have time.
-
- Posts: 52
- Joined: Thu Feb 07, 2013 1:49 pm
- cars: 2002 Camaro
2008 Pontiac G8
Re: Segment Swap utility
yoheer wrote:I'm trying to disable catalytic protection in 12585950 OS
I've disabled DTCs, but i want to disable the system.
The only table i've found is Cat Light off.
Where are the requiered tables?
Cat over temp enrichment table 1x16 at address 8E9C 16 bit scale factor of .000977 set that table to 0 for the adder
Re: Segment Swap utility
More COT tables added.yoheer wrote:I'm trying to disable catalytic protection in 12585950 OS
I've disabled DTCs, but i want to disable the system.
The only table i've found is Cat Light off.
Where are the requiered tables?
Look under converter category
Re: Segment Swap utility
Thnk you guyz
-
- Posts: 590
- Joined: Thu Feb 13, 2020 11:32 pm
- cars: Mainly GM trucks, a Cruze and an Equinox for dailys..
Re: Segment Swap utility
When trying to extract segments from a bunch of files it stops to seek tables... Makes it take a long time.. Is seeking tables required to extract segments?
Seems to be missing some T43 files still.. If I turn off autodetect and point it at the T43.xml it reads them fine.. sample below..
Kind of funny how every t43 seems to have GM_T43 in the bin.. makes it easy for me, lol.. Great work!!!! Many Thanks!!!
Seems to be missing some T43 files still.. If I turn off autodetect and point it at the T43.xml it reads them fine.. sample below..
Kind of funny how every t43 seems to have GM_T43 in the bin.. makes it easy for me, lol.. Great work!!!! Many Thanks!!!