Ve Software
-
- Posts: 1837
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: VE V6 ECU LINKER
I'm always getting into trouble for bringing parts into the house. Lucky she loves me and just piles it up in my little office.
Re: VE V6 ECU LINKER
I made a mistake.
The SPS function i thought was a relearn was an immobilizer(TDM) Flash update for the TDMS with an EEPROM chip
What ive noticed is when you turn the ignition off for more than 6 seconds, Next time you turn ignition on it broadcast the tdm immobilizer code on CAN ID 0x3C9
If ECU is reset or has P0633 (Immobilizer Key Not Programmed) set ecu will save immobilizer data
eg 4988EEFB567D34448341E151A57AB2A6F117 BF8F781C9531 C23EFD
"BF8F781C9531" = Crypto key
"C23EFD" = Key config password
The SPS function i thought was a relearn was an immobilizer(TDM) Flash update for the TDMS with an EEPROM chip
What ive noticed is when you turn the ignition off for more than 6 seconds, Next time you turn ignition on it broadcast the tdm immobilizer code on CAN ID 0x3C9
If ECU is reset or has P0633 (Immobilizer Key Not Programmed) set ecu will save immobilizer data
eg 4988EEFB567D34448341E151A57AB2A6F117 BF8F781C9531 C23EFD
"BF8F781C9531" = Crypto key
"C23EFD" = Key config password
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
perhaps problem i was having as i was programming then trying to start straight after instead of key on and wait. If it's cranking then perhaps it cancels it and doesn't resend so your left to then reset it and start again.
Re: VE V6 ECU LINKER
Ill have to wait for a one to come in to try it out
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
Code reader and Vin write not working on E39 Series 2
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
E39 series 2 can be brute forced at 2 seconds a key (up to 5h 30m).
Must have a bcm connected.
No need to link just reset, will update immobilizer data on a power cycle.
Will be implemented in V0.08.
Must have a bcm connected.
No need to link just reset, will update immobilizer data on a power cycle.
Will be implemented in V0.08.
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
V0.09
Read code from series 2 E39
Read code from series 2 E39
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
Hiya,
Where do you download V0.09? Original post shows V0.01
Where do you download V0.09? Original post shows V0.01
Re: Ve Software
V0.10
- Added E38/E39 Emulated Eeprom read and write
- Added E38/E39 Emulated Eeprom read and write
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
- Knackersjewels
- Posts: 44
- Joined: Thu May 05, 2022 8:24 pm
- cars: 2x VZ alloytec
VY SS L98 ute - Location: Maffra, Vic
- Contact:
Re: Ve Software
Can I get the updated link please mate? I was hoping you updated the file attached to the link you send out, but it's still 0.09