Ve Software
Re: VE V6 ECU LINKER
While testing on an E39 today i noticed if you turn the ignition off for 20 seconds then on again after a reset or link it saves to flash.
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
i think the relink worked on both your tool and tech2 for this E69 VE, this car has other issues, it's cranking and no dash messages other than stability issue (prob rear sensor as known) so it should run, ive read in quite a few places that the "P0633 Immobilizer Key Not Programmed – ECM/PCM" is logged after relinking and goes out once engine is started. I have other fault codes coming up now on this car P0197,118,193,222,122 so ill be chasing down another circuit, this car blew the capacitor off the circuit board on the battery terminals inside the ecu and blew the F35 20amp odd coil circuit fuse.
Re: VE V6 ECU LINKER
Car is up and running, both tools working successfully on E69
Re: VE V6 ECU LINKER
*1/04/22 V0.02
-Added HVAC Single/Dual Zone programming
-Added SIC Sports/Standard mode programming and Vin read/write
-Added HVAC Single/Dual Zone programming
-Added SIC Sports/Standard mode programming and Vin read/write
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
V0.04
-Added IPC Config Programming
Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming
So added the function today
-Added IPC Config Programming
Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming
So added the function today
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
Have you uploaded a download link for V0.04?mattyjf01 wrote:V0.04
-Added IPC Config Programming
Went onsite to do an IPC and EHU
Neither Tech2, Autel or Launch could change EBCM type in the IPC
To get the job done i used my SWCAN VIN programmer for seed key unlock and launch for the config programming
So added the function today
Re: VE V6 ECU LINKER
Looks awesome!
I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.
Has the download link been shared yet?
I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.
Has the download link been shared yet?
Re: VE V6 ECU LINKER
The free demo version isUCMatt wrote:Looks awesome!
I have a VE that I am currently converting from V6 to V8.
Perfect candidate to test your software on.
Has the download link been shared yet?
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
Like I've done with the VZ software I'm adapting it to ELM327 USB and Bluetooth
Here are ones that don't work out of the box The Best one I've found is the forscan with the high/low switch which can be easily modified to be CAN/SWCAN Swap pin 3 -> 1
Swap pin 11 -> 4 (I connected it to 4 and 5) Swapped
Here are ones that don't work out of the box The Best one I've found is the forscan with the high/low switch which can be easily modified to be CAN/SWCAN Swap pin 3 -> 1
Swap pin 11 -> 4 (I connected it to 4 and 5) Swapped
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: VE V6 ECU LINKER
Home Workstation
Taking over the lounge room (The wife loves it)
Taking over the lounge room (The wife loves it)
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203