wideband- needs pull up resistor removed ?
-
- Posts: 1837
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: wideband- needs pull up resistor removed ?
Just for your info you should be measuring the bad earths as a voltage drop when the circuit is operating. Ohms is very misleading and inaccurate way of doing it.
Re: wideband- needs pull up resistor removed ?
VTXU8 - Yep wire from terminal 6 on Spartan lite box to D8 on ecu .
Antus- Yeah it doesn't sound correct and I will recheck again . I don't think it needs to be earthed at ecu ground but will recheck .
Charlescrown- Yes I know , bad habbit really isn't it . I will volt drop it and see if something is wrong .
Thanks guys , will recheck everything again .
Antus- Yeah it doesn't sound correct and I will recheck again . I don't think it needs to be earthed at ecu ground but will recheck .
Charlescrown- Yes I know , bad habbit really isn't it . I will volt drop it and see if something is wrong .
Thanks guys , will recheck everything again .
Re: wideband- needs pull up resistor removed ?
Ok , voltage drops done , all good.
Confirm correct pin D8 on ecu , confirm wire to ecu from Spartan pin 6 on control unit good .
Back out ecu pin/socket that I fitted for D8 connection . Ok looks a little stretched , not good . drag tested female socket on pins of ecu, crap very very loose !
Looks real hard inside of socket and can see some sort of left over bug or wasp or something deep in socket ! Cleaned, re-tensioned socket and confirm fit on ecu pins drag test good ! Cleaned out with pin what ever was in there. Refitted , all good now have live analog signal in TP5 !!!
Far out that done my head in a bit .
The socket I used for making the new connection was out of a spare loom I had , I just pinched the socket with a small 80mm piece of wire from a same colour in donor loom but didn't really look at it very hard , stupid mistake I guess !
Oh well , thanks heaps for the help and tips as usual , cheers guys .
Confirm correct pin D8 on ecu , confirm wire to ecu from Spartan pin 6 on control unit good .
Back out ecu pin/socket that I fitted for D8 connection . Ok looks a little stretched , not good . drag tested female socket on pins of ecu, crap very very loose !
Looks real hard inside of socket and can see some sort of left over bug or wasp or something deep in socket ! Cleaned, re-tensioned socket and confirm fit on ecu pins drag test good ! Cleaned out with pin what ever was in there. Refitted , all good now have live analog signal in TP5 !!!
Far out that done my head in a bit .
The socket I used for making the new connection was out of a spare loom I had , I just pinched the socket with a small 80mm piece of wire from a same colour in donor loom but didn't really look at it very hard , stupid mistake I guess !
Oh well , thanks heaps for the help and tips as usual , cheers guys .
- vlad01
- Posts: 7820
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: wideband- needs pull up resistor removed ?
You literally had a bug in your system
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: wideband- needs pull up resistor removed ?
Yes , yes I did hahahhaa.