Convert V6 Netres To V8
Re: Convert V6 Netres To V8
From what I can see, you cut the 4th leg on the netres and you needed to cut the 5th leg to turn v6 to v8
-
- Posts: 2908
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: Convert V6 Netres To V8
from looking at the netres pictures it still needs that 5th leg for the 7.5k as thats what stock v8 has but removing the 4th(15k resistance) "SHOULD" do the trick but didn't seem to with either of these memcal's!
Re: Convert V6 Netres To V8
Pin numbers start from top left -> bottom left, then bottom right ->top right so the one you cut is pin 13.
You need to re-join that one and cut pin 12 instead.
You need to re-join that one and cut pin 12 instead.
-
- Posts: 2908
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: Convert V6 Netres To V8
AHH bugger the photo that's in earlier post is wrong then, I wish I didn't break it off at the base now but I was pretty sure the photo I had in my memcal folder was the same as what I did last time, but obviously not!
- antus
- Site Admin
- Posts: 8276
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Convert V6 Netres To V8
Yeah, the notch in the diagrams marks the same end as the dot next to pin one in your photos. In general (not just this thread) the way of marking pin one can vary between manufacturers, but the mark is pin 1 or pin 1 end. You can see in your pics that all the chips have some kind of notch, or dot down one end. Thats the chips reference point.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 30
- Joined: Tue Oct 15, 2013 1:04 pm
- cars: X6t
Re: Convert V6 Netres To V8
Has anyone used a VR-VS V6 chip successfully with the netres leg cut and knock board removed when using a stacked $12P tune in the 808? I have heaps of them but have had not had any success.
Cheers
Cheers
Re: Convert V6 Netres To V8
VR V6 chip yes plenty of times. Not socketd yet though but plenty with EEPROM'S fitted.
-
- Posts: 30
- Joined: Tue Oct 15, 2013 1:04 pm
- cars: X6t
Re: Convert V6 Netres To V8
So you have used the in VN-VP with 12P?Dylan wrote:VR V6 chip yes plenty of times. Not socketd yet though but plenty with EEPROM'S fitted.
Re: Convert V6 Netres To V8
Plenty of times. You will need too stack 12P when burning to a VR V6 AUTO memcal as they are 512kb.
- antus
- Site Admin
- Posts: 8276
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Convert V6 Netres To V8
yes 512K bit = 64K Byte so 2 copies of 12P in size (and the second copy is used as its all mapped from the end of the chip, not the start.)
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396